Diabolic Glossy 2:1 *till the end of stock
Acrylic clearcoat
Variants
art. nr.
capacity
quantity per carton
6302
1 l
6
Hardener for Diabolic Clearcoat
6300
0,5 l
6
Gloss grade
high gloss
Description
High-quality acrylic clearcoat with high gloss and increased scratch resistance SR (Scratch Resistant). Designed for specialized car body repairs that require a strong and durable finish.
PERFORMANCE:
1 liter of the mixture is enough to paint 8 ÷ 9 m2 of surface with a a thickness layer of 50 μm.
DEGREES OF MATTING EFFECT
| Gradation Matt | Mixture of Clear Coat (mix before adding hardener) |
Hardener for Clear Coat | Thinner 10% for acrylic systems | |
| DIABOLIC MATT | DIABOLIC GLOSSY | |||
| FULL MAT | 100 ml | —– | 50 ml | 15 ml |
| EGG SHELL | 90 ml | 10 ml | 50 ml | 15 ml |
| SEMI GLOSS | 75 ml | 25 ml | 50 ml | 15 ml |
| FULL GLOSS | —– | 100 ml | 50 ml | 15 ml |
Advantages
- Very good flow.
- High gloss.
- Strong and durable finish.
- High resistance to scratches.
Substrates
Acrylic clearcoats can be applied over:
- Basecoats.
- Old paint coatings in good condition after matting and degreasing.
Important informations
degrease
mixing proportion
2 : 1 + 10%
spraying viscosity
16 ÷ 18s / 20°C
pot life for the mixture
~ 7h / 20°C
2 layers
HVLP / RP
ø1,3 ÷ 1,4 mm
between layers
10 ÷ 15 min.
drying time
24 h / 20°C
Use
Car body repairs that required durable finish.
Mixing proportion per volume
Clearcoat DIABOLIC: 2
Hardener DIABOLIC: 1
Thinner: 10%
Spraying viscosity
16÷18 seconds at 20ºC
Pot life for the mixture
About 7 hours at 20ºC
Number of layers
Number of layers
2 layers evenly applied; about 50-60 µm of dry coating.
RP gun parameters
Nozzle: 1,3÷1,4mm; Pressure: 2,0÷2,2 bar.
HVLP gun parameters
Nozzle: 1,3÷1,4mm; Inlet pressure: 2,0 bar.
Caution: Follow the recommendations of the equipment manufacturer.
Flash off time
Between layers: about 10÷15 min.
Drying time
Dust dry at 20°C: 15 minutes
Baking at 60°C: (temp. of panel) 30 minutes
Ready to polish: after drying overnight.
Temperatures below 20°C significantly increase the drying time.
IR Drying
15÷20 minutes under short wave depending on the total thickness and type of radiator.
Do not exceed maximum temperature of 60°C.
Use according to the recommendations of the equipment manufacturer.
Wait about 10 minutes before starting IR drying.
Performance
1 liter of the mixture is enough to paint 10÷12 m2 of surface with a layer thickness of 50 μm.
Shading
Make sure you have covered all the surface with the clear coat. You should only shade the surface that has been covered and treated. Use InterTroton FADE OUT THINNER to clean any dust or dirt from the surface and to level out the optical gloss differences between the older and new applied coating.
Polishing and eliminating defects
Usually polishing is unnecessary, as the DIABOLIC GLOSSY 2:1 gives the surface a perfect finish immediately after application. However, if some dirt inclusions appear, we recommend removing them and then polishing the surface with an abrasive compound.
General notes
- Do not exceed recommended doses of the hardener!
- The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar. When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
- The rooms should be well ventilated.
- Clean the guns and equipment immediately after use.
Caution: To maintain safety, always follow the instructions given in the MSDS for the products.
Currently, there are no questions and answers related to this product. Be the first one to create an inquiry using the form below.
