NEWSLETTER

Fine

Finish-Polyesterspachtel

Varianten

FarbeArtikelnummerVolumenMenge pro Karton
weiß1050400 g18
weiß1156 1 kg10
weiß1154 1,8 kg10

Glanzgrad

matt
Fine

Technische Dokumentation

Video

Beschreibung

2K-Polyester-Finishspachtel mit sehr guter Haftung auf verschiedenen Untergründen. Ermöglicht das Auftragen in dünnen Schichten, beseitigt Löcher, Kratzer und kleine Unebenheiten. Nach dem Schleifen hinterlässt es eine perfekt glatte Oberfläche.

Vorteile

  • Sehr gute Haftung auf Metall
  • Sehr einfaches Mischen und Anwenden
  • Glatte Oberfläche nach dem Anwenden und Schleifen

Untergrund

Das Produkt weist sehr gute Haftung auf verschiedenen Oberflächen auf. Es kann angewendet werden:

  • auf Stahl und Aluminium nach dem Mattieren und Entfetten
  • auf einen verzinkten Stahl nach dem Mattieren und Entfetten
  • auf angeschliffene Polyester-Glas-Laminate (GFK/GRP), Polyesterspachtel, Acrylgrundierungen, Epoxy-Grundierungen, alte Lackbeschichtungen in gutem Zustand

Empfohlenes Schleifpapier: P80÷P120.

Achtung: Polyesterspachtel darf nicht direkt auf reaktive Grundierungen, 1-Komponenten-Acrylprodukte und Zellulosenitrat-Produkte aufgetragen werden.

Wichtige Informationen zur Verwendung des Produkts

  • Przetrzeć odtłuścić

    degrease

  • Mieszanie wg wagi

    Mixing ratio by weight
    100 : 2

  • Czas życia

    Pot life
    4 ÷ 7 min. / 20°C

  • Czas utwardzania

    Hardening time
    20 ÷ 30 min. / 20°C

  • Szlifowanie

    P80 ÷ P120
    P120 ÷ P320

Anwendungsprozess

  • Zastosowanie
  • Use

    Finishing polyester putty for car repairs.

  • Mieszanie wg wagi
  • Mixing ratio by weight

    Putty: 100
    Hardener: 2

    Stir thoroughly until achieving homogenous paste to not create air inclusions.

  • Czas życia
  • Layer thickness

    Putty can be applied in several thin coats. After each of them the product should dry through. Do not exceed the thickness of 5mm.

    Pot life is 4÷7 minutes at 20°C

  • Żywotność mieszanki Czas utwardzania
  • Hardening time

    20÷30 minutes at 20°C.

    Temperature below 20°C significantly increases the hardening time.

  • Szlifowanie
  • Sanding

    Coarse sanding (dry): P80÷P120,
    Finishing sanding (dry): P120÷P320.

  • Suszenie promieniem IR
  • IR Drying

    5÷7 minutes of short waves, depending on the layer thickness and the type of radiator.
    Do not exceed the temperature of 60°C.
    Use as recommended by the equipment manufacturer.

    Caution: Wait about 5 minutes before the IR drying process

  • Informacja
  • Further work

    Polyester putties can be over coated with:

    • 2K polyester spray fillers.
    • 2K wash primers.
    • 2K acrylic fillers.
    • 2K epoxy fillers.
  • Informacja
  • General notes
    • Excessive amount of hardener will cause problems with bleaching of the top coat!
    • The rooms should be well ventilated.
    • Tools should be washed directly after application.
    • Use personal protection equipment during the 2K products application. Protect the eyes and respiratory system.

    Caution: To maintain safety, always follow the instructions given in the MSDS for
    the products.

Fragen Sie nach Produkt



       
    Siehe auch andere Produkte
    Wyjście 
    Go to top