Variants
color
art. nr.
capacity
quantity in box
gray
2260
0,8 l + 0,2 l
6
white
2252
0,8 l + 0,2 l
6
black
2253
0,8 l + 0,2 l
6
Gloss grade
matt
Description
Bicomponent acrylic filler with high solids content. Characterised by very filling properties, very high adhesion, good stability and good levelling on vertical surfaces. Very easy to apply.
Advantages
- Easy to mix and apply.
- Short hardening time.
- Good isolating and filling properties.
Substrates
Acrylic fillers can be applied over:
- Bare steel and aluminum after matting and degreasing.
- Sanded glass fibre (GFK/GRP).
- Polyester
- Wash primers.
- acrylic fillers.
- Epoxy fillers.
- Old finishes in good condition after flatting and degreasing.
Well prepared surface is necessary for achieving best results. Following sandpaper gradations are recommended:
- by hand (dry or wet): P280÷P320 (GRP P400),
- by machine (dry): P180÷P220.
Important informations
degrease
mixing ratio by weight
4 : 1 + 15 ÷ 20%
spray viscosity
30÷50 sec in 20°C
mixture pot life
60 min / 20°C
2÷3 layer
HVLP / RP
ø1,6 ÷ 2,0 mm
between layers
approx. 5÷10 min
before baking
approx. 10 min
hardening time
approx. 3÷4 h in 20°C.
approx. 30 min in 60°C.
P320 ÷ P500
P600÷P1000
Use
For car repairs as a filling or grounding filler.
Mixing ratio by volume
Filler: 4 parts
Hardener: 1 part
Thinner: 15÷20%
Stir thoroughly until achieving homogenous mixture
Spraying viscosity
30÷50 seconds at 20°C
Pot life
approx. 60 min. at20°C
Number of layers
2-3layers of 150÷300µm thickness
RP gun parameters:
Nozzle: 1,6÷2,0 mm, Pressure: 2,0÷2,2 bar
HVLP gun parameters:
Nozzle: 1,5÷1,9 mm; Pressure: 2,0 bar
Evaporation time
Between the layers: approx. 5÷10 minutes
Before baking: approx. 10 minutes
Evaporation time depends on the temperature and the number of layers.
Hardening time
Approx. 3-4 hours at 20°C
Approx. 30 min. at 60°C
Temperature below 20°C significantly increases the hardening time.
IR drying
10÷15 minutes of short waves for the thickness of 150÷250 µm.
Do not exceed 60°C.
Use as recommended by the equipment manufacturer.
Wait about 10 minutes before starting the heater drying.
Dry sanding
By machine P320÷P500.
By hand P320÷P500.
Wet sanding
By machine P600÷P1000.
By hand P800÷P1000.
Further work
2K acrylic fillers can be directly over coated with:
- 2K acryl top coats.
- 1K base coats.
General notes
- Do not exceed recommended doses of hardener!
- The best repair results can be achieved at room temperature. Temperature in body shop and temperature of a product should be the same.
- When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and respiratory system.
- Clean the guns and equipment immediately after use.1
- The rooms should be well ventilated.
Caution: To maintain safety, always follow the instructions given in the MSDS for the products.
Currently, there are no questions and answers related to this product. Be the first one to create an inquiry using the form below.