C38 VHS 2:1

Acrylic clear coat

1 8

Share product information


art. nr.


quantity per carton


1 l



5 l


hardener for clear coat

standard 13091

0,5 l


standard 13093

2,5 l


fast 13101

0,5 l


fast 13102

2,5 l


slow 14268

0,5 l


slow 14269

2,5 l


Gloss grade

high gloss

1 8

Share product information


High-quality 2K acrylic clearcoat for car repairs with a very low content of volatile compounds. The short drying time (3 hours at 20 ° C) combined with the extended pot life of the mixture allows for partial and overall paiting of the entire car body.

1 liter of the mixture is enough to paint 10 m2 of surface with a a thickness layer of 60 μm.


  • For the repair of small and large areas.
  • Very high solids content >55%.
  • Excellent finish.
  • Easy application.
  • Great overspray absorption.
  • Perfect flow.


Acrylic clearcoats can be applied over:

  • Basecoats.
  • Old paint coatings in good condition after matting and degreasing.

Important informations


mixing proportion
2 : 1 + 0 +5%

spraying viscosity
17 ÷ 19s / 20°C

pot life for the mixture
3,5 h / 20°C

1,5 ÷ 2,0 layers
ø1,2 ÷ 1,4 mm

between layers
5 ÷ 10 min

before baking
10 min

drying time
3 h / 20°C
15 min. / 60°C
(for standard hardener)

Application process


For car body repair of small and large surfaces.

Mixing proportion per volume

Clearcoat: 2
Hardener: 1
Thinner for acrylic systems: 0-5%

Spraying viscosity

17÷19 seconds at 20ºC DIN4

Pot life for the mixture

(double viscosity, the clearcoat cannot be used)
3,5 hours at 20ºC (standard hardener)
2 hours at 20ºC (fast hardener)

Gun parameters

RP Nozzle: 1,2÷1,4mm; Pressure: 2,0÷2,2 bar.
HVLP Nozzle: 1.3÷1,4mm; Inlet pressure: 2,0 bar.
Caution: Follow the recommendations of the equipment manufacturer.
- 1,5 layers – 1 medium, thin layer and one full coat with 2 minutes flash off between coats to obtain a dry film thickness of 50-60 µm,
- 2 layers - 2 full layers with a 5-10 minutes flash-off time to obtain a dry film thickness of 60-75 μm,

Flash off time for standard and fast hardener

Between layers: 5-10 min
Before baking: 10 min

Drying time for standard hardener

Dust dry: 40 min./20°C, 10 min./60°C
Touch dry: 3 hour/20°C, 15 min./60°C
Ready to use: 13 hours/20°C, 15 min./60°C+4 hours/20°C
Final drying: 7 days/20°C, 15 min/60°C+4 days/20°C

IR Drying

10÷15 minutes under short wave depending on the total thickness and type of radiator.
Do not exceed maximum temperature of 60°C.
Use according to the recommendations of the equipment manufacturer.
Wait about 10 minutes before starting IR drying.


1 liter of the mixture is enough to paint 10 m2 of surface with a layer thickness of 60 μm.

Polishing and eliminating defects

Usually polishing is unnecessary, as the C38 VHS Clear Coat 2:1 gives the surface a perfect finish immediately after application. However, if some dirt inclusions appear, we recommend removing them and then polishing the surface with an abrasive compound.

General notes

- Do not exceed recommended doses of the hardener!
- The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar. When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
- The rooms should be well ventilated.
- Clean the guns and equipment immediately after use.

Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Questions and answers

Currently, there are no questions and answers related to this product. Be the first one to create an inquiry using the form below.

Ask about this product

    Check the tips regarding the product