Variants
color
art. no.
capacity
quantity per carton
transparent
14937
1 l
6
transparent
14938
5 l
4
hardener for clear coat
standard
14942
0,5 l
6
standard
14945
2,5 l
4
fast
14943
0,5 l
6
fast
14946
2,5 l
4
slow
14944
0,5 l
6
slow
14947
2,5 l
4
Gloss grade
high gloss
Description
2-component acrylic clearcoat with high gloss and increased resistance to scratches SR (Scratch resistant). Characterized by its universal use. Clear coat features easy application and is ready to use without the addition of thinner. The availability of 3 versions of hardener (standard, fast, slow) allows working in different temperature conditions.
EFFICIENCY:
1 litr of the mixture is sufficient to cover 8 m2 with 50 μm of layer thickness.
Advantages
- Ready to use without the addition of thinner.
- Easy application and universal in use.
- High gloss.
- Hard and durable finish.
- Increased scratch resistance.
- Good fluidity.
Substrates
ZIRCON MS 2:1 2K acrylic clearcoat can be applied over:
- Base coats.
- Existing coatings in good condition after sanding and degreasing.
Important informations
degrease
mixing ratio
2 : 1 + 0 %
spraying viscosity
15 ÷ 17s / 20°C
pot life for the mixture
5 h / 20°C
2-3 layers
HVLP / RP
ø1,3 ÷ 1,4 mm
between layers
5 ÷ 10 min.
before baking
approx. 10 min.
drying time
30 min. / 60°C
15÷20 min.
Use
For car body repairs that require a durable finish.
Mixing ratio by volume
Clear coat 2
Hardener: 1
Thinner: 0%
Spraying viscosity
15÷17 seconds at 20°C
Pot life for the mixture
about 5 hours at 20°C
Number of layers
2-3 full layers, dry thickness of a single layer approx. 30 µm
RP gun parameters
Nozzle: 1.3÷1.4 mm; Pressure: 2,0÷2,2 bar.
HVLP gun parameters
Nozzle: 1.3÷1.4 mm; Inlet pressure: 2,0 bar.
Flash off time
Betwee layers: 5 ÷ 10 minutes
Before baking: about 10 minutes
Drying time
Dust free: about 30-35 min.
Ready to polish: after drying overnight
Drying time at 60°C
Clearcoat is ready to polish after baking for about 30 minutes and cooling down (about 2 hours).
Temperatures below 20°C significantly increases the drying time.
IR drying
15÷20 minutes under short wave depending on the total thickness and type of radiator.
Do not exceed maximum temperature of 60°C.
Use according to the recommendations of the equipment manufacturer.
Wait about 10 minutes before starting IR drying.
Performance
1 litre of the mixture is sufficient to coat 8 m2 with 50 μm of layer thickness.
Shading
Make sure you have covered all the surface with the clear coat. You should only shade the surface that has been covered and treated. Use InterTroton FADE OUT THINNER to clean any dust or dirt from the surface and to level out the optical gloss differences between the older and new applied coating.
Polishing and eliminating defects
Usually polishing is unnecessary, as the ZIRCON MS 2:1 gives the surface a perfect finish immediately after application. However, if some dirt inclusions appear, we recommend removing them and then polishing the surface with an abrasive compound.
General notes
-Do not exceed recommended doses of the hardener!
-The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar. When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
-The rooms should be well ventilated.
- Clean the guns and equipment immediately after use.
Caution: To maintain safety, always follow the instructions given in the MSDS for the products.
Currently, there are no questions and answers related to this product. Be the first one to create an inquiry using the form below.