NEWSLETTER

C2007 UHS 2:1

Acrylic clear coat

Variants

ColorArt. no. CapacityQuantity per box
transparent12941 l6
transparent13075 l4
Hardener for clear coat
standard1295 0,5 l6
standard18532,5 l4
fast1852 0,5 l6
fast14692,5 l4
slow19090,5 l6
slow84402,5 l4

Gloss grade

high gloss
C2007 UHS 2:1

Technical documentation

Video

Description

2K acrylic clearcoat with ultra high solids content for car body repairs. Ideal for whole car body repair with perfect leveling and great resistance to UV rays and other harmful climatic conditions. The product is ready to use without the addition of thinner, easy to mix and apply.

PERFORMANCE:

1 liter of the mixture is enough to paint 10 ÷ 12 m2 of surface with a layer thickness of 50÷60 μm.

Advantages

  • High solids content.
  • Excellent coat appearance.
  • Very high gloss.
  • Easy to mix and apply (no thinner required).

Substrates

Acrylic clearcoats can be applied over:

  • Basecoats.
  • Old paint coatings in good condition after matting and degreasing.

Important informations

  • Przetrzeć odtłuścić

    degrease

  • Proporcje mieszania

    mixing proportion
    2 : 1

  • Lepkość natryskowa

    spraying viscosity
    18 ÷ 20s / 20°C

  • Żywotność mieszanki

    pot life for the mixture
    1,5 h / 20°C

  • Liczba warstw

    2 layers
    HVLP / RP
    ø1,2 ÷ 1,4 mm

  • Czas odparowania

    between layers
    7 ÷ 8 min

  • Czas odparowania

    before baking
    15 min.

  • Czas utwardzania

    drying time
    30 min. / 60°C

Application process

  • Zastosowanie
  • Use

    Paint repairs on small and large surfaces.

  • Proporcje mieszania
  • Mixing ratio by volume

    Clearcoat: 2
    Hardener: 1
    Thinner for acrylic systems: 0%

  • Lepkość natryskowa
  • Spraying viscosity

    18÷20 sec at 20°C

  • Liczba warstw
  • Gun parameters

    Number of layers
    2 thin layers, dry film thickness: about 60μm.
    RP gun parameters
    Nozzle: 1.2÷1.4 mm; Pressure: 2,0÷2,2 bar.
    HVLP gun parameters
    Nozzle: 1.3÷1.4 mm; Inlet pressure: 2,0 bar.

  • Czas odparowania
  • Flash off time

    Between layers: 7-8 min.
    Before baking: 15 min.

  • Czas utwardzania
  • Drying time

    Drying time at 20ºC
    Dust free: about 35-40 min.
    Drying time at 60°C
    Clear coat is ready to polish after baking for about 30 minutes and approx. 2 hours after cooling of the coating.

    Temperatures below 20°C significantly increases the drying time.

  • Suszenie promieniem IR
  • IR drying

    15÷20 minutes under short wave depending on the total thickness and type of radiator.
    Do not exceed maximum temperature of 60°C.
    Use according to the recommendations of the equipment manufacturer.
    Wait about 10 minutes before starting IR drying.

  • Informacja
  • Performance

    1 liter of mixture is enough to cover 10÷12 m2 with a dry layer with thickness of 50÷60 μm.

  • Informacja
  • Polishing and eliminating defects

    Usually polishing is unnecessary, as the C2007 UHS 2:1 gives the surface a perfect finish immediately after application. However, if some dirt inclusions appear, we recommend removing them and then polishing the surface with an abrasive compound.

  • Informacja
  • General notes

    – Do not exceed recommended doses of the hardener!
    – The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar. When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
    – The rooms should be well ventilated.
    – Clean the guns and equipment immediately after use.

    Caution:
    To maintain safety, always follow the instructions given in the MSDS for the products.

Ask about this product



       
    See also other products
    Wyjście 
    Go to top