C88 Premium Speed HS 2:1

Acrylic clearcoat


ColorArt. No.Capacity Quantity per carton
transparent11012 1 l6
transparent113205 l4
Hardener for clearcoat
standard151970,5 l6
standard15198 2,5 l4
fast110130,5 l6
fast113212,5 l4

Gloss grade

high gloss
C88 Premium Speed HS 2:1



High-quality 2K acrylic clearcoat for quick car body repairs with low VOC and increased scratch resistance SR (Scratch Resistant). Thanks to the use of modern raw materials, the C88 PREMIUM HS clearcoat is characterized by its short drying time and optimal working window, allowing for a coating with high and durable gloss.

1 liter of the mixture is enough to paint 8 ÷ 10 m2 of surface with a a thickness layer of 60 μm.


  • Short drying time.
  • High solids content.
  • Very high gloss.
  • Perfect finish.
  • Great resistance to UV rays and atmospheric conditions.
  • Excellent flow and easy application.


Acrylic clearcoats can be applied over:

  • Basecoats.
  • Old paint coatings in good condition after matting and degreasing.

Important informations

  • Przetrzeć odtłuścić


  • Proporcje mieszania

    mixing proportion
    2 : 1 + 0 + 5 %

  • Lepkość natryskowa

    spraying viscosity
    15 ÷ 17s / 20°C

  • Żywotność mieszanki

    pot life for the mixture
    2,5 h / 20°C

  • Liczba warstw

    2 layers
    HVLP / RP
    ø1,3 ÷ 1,4 mm

  • Czas odparowania

    between layers
    4 ÷ 5 min.

  • Czas odparowania

    before baking
    10 min

  • Czas utwardzania

    drying time
    3 h / 20°C
    15 min. / 60°C

Application process

  • Zastosowanie
  • Use

    Fast car body repairs that required durable finish.

  • Proporcje mieszania
  • Mixing proportion per volume

    Clearcoat: 2
    Hardener: 1
    – with standard hardener 0-5%
    – with fast hardener 10%

    * it is not recommended the use of accelerators and fast express thinners.

  • Lepkość natryskowa
  • Spraying viscosity

    15÷17 seconds at 20ºC DIN4

  • Żywotność mieszanki
  • Pot life for the mixture

    About 2,5 hours at 20ºC

  • Liczba warstw
  • Gun parameters

    Number of layers: 2 full layers; about 50÷60 µm of dry coating.
    RP Nozzle: 1,3÷1,4mm; Pressure: 2,0÷2,2 bar.
    HVLP Nozzle: 1.3÷1,4mm; Inlet Pressure: 2,0 bar.

    Caution: Follow the recommendations of the equipment manufacturer.

  • Czas odparowania
  • Flash off time

    Between layers: about 4÷5 min.
    Before baking: 10 min.

    *Flash off time depends on the type of painting booth.

  • Czas utwardzania
  • Drying time for STANDARD hardener

    Dust dry: 30 min./20°C, 10 min./60°C
    Touch dry: 2,5 godz./20°C, 15 min./60°C
    Ready to use: 8 godz./20°C, 15 min./60°C+3 godz./20°C
    Final drying: 7 dni/20°C, 15 min/60°C+3 dni/20°C

    * Temperatures below 20°C significantly increase the drying time.

  • Suszenie promieniem IR
  • IR Drying

    10÷15 minutes under short wave depending on the total thickness and type of radiator.
    Do not exceed maximum temperature of 60°C.
    Use according to the recommendations of the equipment manufacturer.
    Wait about 10 minutes before starting IR drying.

  • Informacja
  • Performance

    1 liter of the mixture is enough to paint 8÷10 m2 of surface with a layer thickness of 60 μm.

  • Informacja
  • Shading

    Make sure you have covered all the surface with the clear coat. You should only shade the surface that has been covered and treated. Use InterTroton FADE OUT THINNER to clean any dust or dirt from the surface and to level out the optical gloss differences between the older and new applied coating.

  • Informacja
  • Polishing and eliminating defects

    Usually polishing is unnecessary, as the C18 VHS Clear Coat 2:1 gives the surface a perfect finish immediately after application. However, if some dirt inclusions appear, we recommend removing them and then polishing the surface with an abrasive compound.

  • Informacja
  • General notes
    • Do not exceed recommended doses of the hardener!
    • The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar. When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
    • The rooms should be well ventilated.
    • Clean the guns and equipment immediately after use.

    Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Ask about this product


    Related products

    See also other products
    Go to top