2K Anticorrosive Epoxy Primer 4:1

Epoxy Primer for RANGERS


colorart. no. capacityquantity per box
light grey 152600,8l + 0,2l6

Gloss grade

2K Anticorrosive Epoxy Primer 4:1


High-quality 2-component epoxy primer with anti-corrosion additives designed specifically for use under Rangers 2K polyurethane protective coating. It perfectly protects steel surfaces from corrosion in the automotive repair process, while strengthening and prolonging the anti-corrosive effect of the Rangers protective coating. At high dilution, it can be applied using wet-on-wet technique.


  • Excellent protection of steel surfaces..
  • Very good adhesion to various surfaces.
  • Easy application process and smooth spreadability.


Rangers Anticorrosive Epoxy Primer 4:1 can be applied over:

  • Steel and aluminum after matting and degreasing.
  • Galvanized steel after matting and degreased.
  • Sanded polyester/glass laminates (GRP/GRP) and epoxy-glass.
  • Polyester and epoxy putties.
  • Old coatings in good condition after matting and degreasing.

Good surface preparation is essential to achieve the best repair results.

Important informations

  • Przetrzeć odtłuścić


  • Proporcje mieszania

    mixing proportions
    4 : 1 + 15%
    4 : 1 + 25%
    4 : 1 + 50%

  • Lepkość natryskowa

    spray viscosity
    4 : 1 + 15%
    4 : 1 + 25%
    4 : 1 + 50%

  • Żywotność mieszanki

    pot life
    approx. 3h at 20°C

  • Liczba warstw

    number of layers
    2 ÷ 3 layers
    HVLP / RP
    Ø 1.5 ÷ 2.0 mm

  • Czas odparowania

    between layers: 5 ÷ 10 min.

  • Czas odparowania

    before baking: about 10 min.

  • Czas utwardzania

    hardening time
    8 h / 20°C
    45 minutes/ 60°C

  • Szlifowanie na sucho

    P360 ÷ P500

  • Szlifowanie na mokro

    P600 ÷ P1000

Application process

  • Zastosowanie
  • Use

    For car repairs as a filling primer or isolation primer for sending or wet wet technique.

  • Proporcje mieszania
  • Mixing ratio by volume

    Primer : 4
    Hardener : 1
    Thinner :
    – 15% as filling primer
    – 25% as grounding primer
    – 50% as wet on wet

    Stir thoroughly until achieving homogenous mixture.

  • Lepkość natryskowa
  • Spraying viscosity

    55 ÷ 60 seconds at 20°C for the filling version (at 15% thinner)
    35 ÷ 40 seconds at 20°C for the grounding version (at 25% thinner)
    18 ÷ 20 seconds at 20°C for wet on wet version (at 50% thinner)

  • Żywotność mieszanki
  • Pot life

    about 3 hours at 20°C

  • Liczba warstw
  • Numbers of layers

    2 ÷ 3 layers

    Recommended layer thickness:
    • isolation primer: 50÷70µm dry film.
    • filling primer, for sanding: 200÷250µm dry film.

    RP gun parameters
    Nozzle: 1,6÷2,0 mm; Pressure: 2,0-2,2 bar.

    HVLP gun parameters
    Nozzle: 1,5÷1,9 mm; Inlet pressure: 2,0 bar.

  • Czas odparowania
  • Evaporation time

    between layers: 5-10 minutes
    before baking: approx. 10 minutes
    before applying clearcoat (wet on wet): 60-120 minutes

    Evaporating time depends on temperature and layer thickness

  • Czas utwardzania
  • Hardening time

    about 8 hours at 20°C (depending on the layer thickness)
    about 45 minutes at 60°C (depending on the layer thickness)

    Temperature lower than 20°C is extending hardening time.

  • Suszenie promieniem IR
  • IR drying

    10÷15 minutes under short wave for thickness 150÷200µm
    Do not exceed 60°C.
    Use as recommended by the equipment manufacturer.
    Wait about 10 minutes before starting the heater drying.

  • Szlifowanie na sucho
  • Dry sanding

    Grinding Machine: P360÷P500.
    Hand Sanding: P280÷P320.

  • Szlifowanie na mokro
  • Wet sanding

    Grinding Machine: P600÷P1000.
    Hand sanding: P800÷P1000.
    Wet on wet does not require sanding!

  • Informacja
  • Further works

    2-component Anticorrosive epoxy primer Rangers can be applied over:

    • 2-component polyurethane protective coating Rangers.
    • 2-component topcoats.
    • 1-component basecoats.
    • 2-component acrylic primers.
    • 2-component polyester putties.
    • 2-component epoxy putties.
  • Informacja
  • General notes
    • Do not exceed recommended doses of the hardener!
    • The best repair results can be achieved at room temperature. The temperature in the body shop and the temperature of the product should be similar
    • When working with 2K products, it is recommended to use personal protection.
      equipment. Protect the eyes and respiratory system.
    • Clean the guns and equipment immediately after use.
    • The rooms should be well ventilated.

    Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Ask about this product


    Related products

    See also other products
    Go to top