Top Coat RAL Colours

Acrylic top coat MS 2:1


Colour Art. No.CapacityQuantity per box
RAL 1003 (yellow)139011 l6
139023,75 l4
RAL 1028 (yellow)136441 l6
13645 3,75 l4
RAL 3020 (red)136461 l6
13647 3,75 l4
RAL 5005 (blue)136511 l6
13652 3,75 l4
RAL 6005 (green)141391 l6
141403,75 l4
RAL 7035 (light grey)141411 l6
141423,75 l4
RAL 7016 (anthracite)139031 l6
13904 3,75 l4
RAL 7021 (grey-black)136491 l6
13650 3,75 l4
RAL 9005 (black)20681 l6
2047 3,75 l4
RAL 9010 (white)20481 l6
20353,75 l4
RAL 9016 (white) 20371 l6
20663,75 l4
Hardener for acrylic paint MS 2:1
standard13707 0,5 l6
137081 l1
fast137330,5 l6
137341 l1

Gloss grade

high gloss
Top Coat RAL Colours



2-component acrylic topcoat with increased scratch resistance SR (Scratch Resistant) and highly resistant to climatic factors. Features perfect finish immediately after application. Does not require clear coat.


  • Very glood flow.
  • High covering.
  • Strong and durable finish.


Acrylic topcoats can be applied over:

  • 2K acrylic primers.
  • 2K epoxy primers.
  • Old paint coatings in good condition after matting and degreasing.

Good surface preparation is essential to achieve the best repair results.

Important informations

  • Przetrzeć odtłuścić


  • Proporcje mieszania

    Mixing ratio
    2 : 1 + 10%

  • Lepkość natryskowa

    Spraying viscosity
    18 ÷ 21s / 20°C

  • Żywotność mieszanki

    Pot life
    ok. 8 h / 20°C

  • Liczba warstw

    2 layers
    HVLP / RP
    ø1,3 ÷ 1,4 mm

  • Czas odparowania

    between layers
    ok. 5 min.

  • Czas odparowania

    before baking
    ~10 min.

  • Czas utwardzania

    Drying time
    20 min. / 60°C

Application process

  • Zastosowanie
  • Use

    Dedicated for carbody repairs that require a durable finish.

  • Proporcje mieszania
  • Mixing ratio by volume

    Clear coat: 2
    Hardener: 1
    Thinner: 10%

  • Lepkość natryskowa
  • Spraying viscosity

    18÷21 seconds at 20°C.

  • Żywotność mieszanki
  • Pot life for the mixture

    About 8 hours at 20°C.

  • Liczba warstw
  • Number of layers

    2 full layers.
    RP gun parameters
    Nozzle: 1.3÷1.4 mm; Pressure: 2,0÷2,2 bar.
    HVLP gun parameters
    Nozzle: 1.3÷1.4 mm; Inlet pressure: 2,0 bar.
    Pressure – according to the recommendations of the equipment manufacturer.

  • Czas odparowania
  • Flash off time

    Between layers: about 5 minutes
    Before baking: about 10 minutes

  • Czas utwardzania
  • Drying time

    Dust dry at 20°C: about 15 minutes
    Baking at 60°C: about 20 minutes

    Temperatures below 20°C significantly increases the drying time.

  • Informacja
  • Performance

    1 liter of the mixture is enough to paint a surface of 8 ÷ 10 m2 with a layer of 50 μm.

  • Informacja
  • Polishing and eliminating defects

    Usually polishing is unnecessary, as the RAL Acrylic Clear Coat gives the surface a perfect look immediately after use. However, if some dirt inclusions appear, it is recommended to remove them using with polishing compound.

  • Informacja
  • General information
    • Do not exceed recommended doses of hardener!
    • The best repair results can be achieved by painting at room temperature. Temperature in the body shop and temperature of the product should be the same.
    • When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and air ways.
    • The rooms should be well ventilated.
    • Clean the guns and equipment immediately after use.

    Caution: To maintain safety, always follow the instructions given in the MSDS of the products.

Ask about this product

    Go to top