color | art. no. | capacity | quanityt per carton |
RAL 1003 (yellow) | 13901 | 1 l | 6 |
13902 | 3,75 l | 4 | |
RAL 1028 (yellow) | 13644 | 1 l | 6 |
13645 | 3,75 l | 4 | |
RAL 3020 (red) | 13646 | 1 l | 6 |
13647 | 3,75 l | 4 | |
RAL 5005 (blue) | 13651 | 1 l | 6 |
13652 | 3,75 l | 4 | |
RAL 6005 (green) | 14139 | 1 l | 6 |
14140 | 3,75 l | 4 | |
RAL 7035 (light grey) | 14141 | 1 l | 6 |
14142 | 3,75 l | 4 | |
RAL 7016 (anthracite) | 13903 | 1 l | 6 |
13904 | 3,75 l | 4 | |
RAL 7021 (grey-black) | 13649 | 1 l | 6 |
13650 | 3,75 l | 4 | |
RAL 9005 (black) | 2068 | 1 l | 6 |
2047 | 3,75 l | 4 | |
RAL 9010 (white) | 2048 | 1 l | 6 |
2035 | 3,75 l | 4 | |
RAL 9016 (white) | 2037 | 1 l | 6 |
2066 | 3,75 l | 4 | |
Hardener for acrylic paint MS 2:1 | |||
standard | 13707 | 0,5 l | 6 |
13708 | 1 l | 1 | |
fast | 13733 | 0,5 l | 6 |
13734 | 1 l | 1 |
2-component acrylic topcoat with increased scratch resistance SR (Scratch Resistant) and highly resistant to climatic factors. Features perfect finish immediately after application. Does not require clear coat.
Acrylic topcoats can be applied over:
Good surface preparation is essential to achieve the best repair results.
degrease
mixing ratio
2 : 1 + 10%
spraying viscosity
18 ÷ 21s / 20°C
pot life for the mixture
ok. 8 h / 20°C
2 layers
HVLP / RP
ø1,3 ÷ 1,4 mm
between layers
ok. 5 min.
before baking
~10 min.
drying time
20 min. / 60°C
Dedicated for carbody repairs that require a durable finish.
Clear coat: 2
Hardener: 1
Thinner: 10%
18÷21 seconds at 20°C.
About 8 hours at 20°C.
2 full layers.
RP gun parameters
Nozzle: 1.3÷1.4 mm; Pressure: 2,0÷2,2 bar.
HVLP gun parameters
Nozzle: 1.3÷1.4 mm; Inlet pressure: 2,0 bar.
Pressure – according to the recommendations of the equipment manufacturer.
Between layers: about 5 minutes
Before baking: about 10 minutes
Dust dry at 20°C: about 15 minutes
Baking at 60°C: about 20 minutes
Temperatures below 20°C significantly increases the drying time.
1 liter of the mixture is enough to paint a surface of 8 ÷ 10 m2 with a layer of 50 μm.
Usually polishing is unnecessary, as the RAL Acrylic Clear Coat gives the surface a perfect look immediately after use. However, if some dirt inclusions appear, it is recommended to remove them using with polishing compound.
– Do not exceed recommended doses of hardener!
– The best repair results can be achieved by painting at room temperature. Temperature in the body shop and temperature of the product should be the same.
– When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and air ways.
– The rooms should be well ventilated.
– Clean the guns and equipment immediately after use.
Caution: To maintain safety, always follow the instructions given in the MSDS of the products.